This is the model generator for Gridfinity Extended .
Any changes you make are saved in the URL, so you can share that URL or create a bookmark to keep those changes around.
README .gridfinity_basic_cup ,
gridfinity_baseplate ,
gridfinity_item_holder ,
gridfinity_drawers ,
gridfinity_lid ,
gridfinity_marble ,
gridfinity_tray ,
gridfinity_vertical_divider ,
stanley_basic_cup ,
gridfinity_baseplate_flsun_q5 ,
gridfinity_chess ,
gridfinity_glue_stick ,
gridfinity_sieve ,
gridfinity_silverware_legacy ,
gridfinity_silverware ,
gridfinity_sliding_lid ,
gridfinity_socket_holder
render_ choice
select what to render
position
drawer_ inner_ width
Inner width of drawer in Gridfinity units
drawer_ inner_ depth
Inner depth of drawer in Gridfinity units
drawer_ inner_ height
Inner height of drawer in Gridfinity units
drawer_ count
Number of drawers
drawer_ enable_ custom_ sizes
drawer_ custom_ sizes
Inner height of drawer in Gridfinity units. Edit in script for more than 4 items.
drawer_ clearance
Add clearance inside the drawers for the bins. Width, depth and height. Default is 0.25
chest_ clearance
Add clearance inside the chest for the drawer. width, depth and height. Default is 0.25
chest_ wall_ thickness
Wall thickness of the chest.
chest_ drawer_ slide_ thickness
Thickness of drawer slides in mm. 0 is uses wall thickness.
chest_ drawer_ slide_ width
Width of drawer slies in mm. 0 is full chest width.
handle_ size
Handle size width, depth, height, and radius. Height, less than 0 drawerHeight/abs(height). radius, -1 = depth/2.
handle_ vertical_ center
handle_ cut_ factor
handle_ rotate
drawer_ wall_ thickness
drawer_ base
drawer_ enable_ magnet
drawer_ magnet_ size
chest_ top_ wallpattern_ style
chest_ top_ style
Plate Style
chest_ top_ base_ plate_ enable_ magnets
Enable magnets in the bin corner
chest_ top_ base_ plate_ magnet_ size
(Zack's design uses magnet diameter of 6.5, 2.4)
chest_ top_ base_ plate_ reduced_ wall_ height
Reduce the frame wall size to this value
chest_ top_ base_ plate_ reduced_ wall_ taper
chest_ bottom_ wallpattern_ style
chest_ bottom_ grid
chest_ leg_ clearance
Fit clearance of chest feet
magnet_ diameter
(Zack's design uses magnet diameter of 6.5)
screw_ depth
(Zack's design uses depth of 6)
hole_ overhang_ remedy
Sequential Bridging hole overhang remedy is active only when both screws and magnets are nonzero (and this option is selected)
chest_ corner_ attachments_ only
Only add attachments (magnets and screw) to chest corners (prints faster).
sub_ pitch
AKA half pitch. Enable to subdivide bottom pads to allow sub-cell offsets
flat_ base
Removes the internal grid from base the shape
wallpattern_ border_ width
wall pattern border width. -1 defaults to chest_wall_thickness. less than 0 chest_wall_thickness/abs(wallpattern_border_width)
efficient_ back
wallpattern_ enabled
Grid wall patter
wallpattern_ style
Style of the pattern
wallpattern_ strength
Spacing between pattern
wallpattern_ walls
wall to enable on, front, back, left, right.
wallpattern_ rotate_ grid
rotate the grid
wallpattern_ cell_ size
Size of the hole
wallpattern_ dividers_ enabled
Add the pattern to the dividers
wallpattern_ hole_ sides
Number of sides of the hole op
wallpattern_ hole_ radius
Radius of corners
wallpattern_ fill
pattern fill mode
wallpattern_ border
border around the wall pattern, default is wall thickness
wallpattern_ depth
depth of imprint in mm, 0 = is wall width.
wallpattern_ pattern_ grid_ chamfer
grid pattern hole taper
wallpattern_ pattern_ voronoi_ noise
voronoi pattern noise,
wallpattern_ pattern_ brick_ weight
brick pattern center weight
wallpattern_ pattern_ quality
$fs for floor pattern, min size face.
fa
minimum angle for a fragment (fragments = 360/fa). Low is more fragments
fs
minimum size of a fragment. Low is more fragments
fn
number of fragments, overrides $fa and $fs